|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thanks God for the internet and thanks for the service like this - proffessional solution on time.
;
About the service it's very fast and reliable. About the manual the quality is high enough to read even the tiniest details on the wiring diagrams so you can't ask much more than that, let it alone for a manual of a product from 20 years ago. Thank you, very satisfied.
;
The downloaded quality was as good as the orignial
 ;
This is a great and complete Service Manual for the Sharp GF8585HB. Giving full and detailed technical insight. Good to find these manuals online.
;
Everything was ok with the manual. If I have a small complaint, is that I ordered it during the weekend and I think you guys were closed. But I did receive it late Sunday. I will surely order from you again
6. FLASH MEMORY
The decoder board supports 70ns Flash memories. Currently 4 configurations are supported: FLASH_512K_8b FLASH_1024K_8b FLASH_512Kx2_8b FLASH_512Kx2_16b The MT1379 permits both 8- and 16-bit common memory I/O accesses with a removable storage card via the host interface.
7. SERIAL EEPROM MEMORY
An I2C serial EEPROM is used to store user configuration (i.e. language preferences, speaker setup, etc.) and software configuration.. Industry standard EEPROM range in size from 1kbit to 256kbit and share the same IC footprint and pinout. The default device is 2kbit, 256kx 8, SOIC8 SGS Thomson ST24C02M1 or equivalent.
8. AUDIO INTERFACE AUDIO SAMPLING RATE CONFIGURATION
AND
PLL COMPONENT
The MT1379 audio mode configuration is selectable, allowing it to interface directly with 2 low-cost audio DACs and ADCs. The audio port provides a standard I S interface input and 2 output and S/PDIF (IEC958) audio output. Stereo mode is in I S format while six channels Dolby Digital (5.1 channel) audio output can be channeled through the S/PDIF. The S/PDIF interface 2 consists of a bi-phase mark encoder, which has low skew. The transmit I S interface supports the 112, 128, 192, 256, 384, and 512 sampling frequency formats, where sampling frequency Fs is 2 usually 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, or 192 kHz. The audio samples for the I S transmit interface can be 16, 18, 20, 24, and 32-bit samples. For Linear PCM audio stream format, the MT1379 supports 48 kHz and 96 kHz. Dolby Digital audio only supports 48 kHz. The MT1379 incorporates a built-in programmable analog PLL in the device architecture in order to generate a master audio clock. The MCLK pin is for the audio DAC clock and can either be an output from or an input to the MT1379. Audio data out (TSD) and audio frame sync (TWS) are clocked out of the MT1379 based on the audio transmit bit clock (TBCK). Audio receive bit clock (RBCK) is used to clock in audio data in (RSD) and audio receive frame sync (RWS).
9. FRONT PANEL
9.1 VFD CONTROLLER
The VFD controller is a NEC uPD16311. This controller is not a processor, but does include a simple state machine which scans the VFD and reads the front panel button matrix. The 16311 also includes RAM so it can store the current state of all the VFD icons and segments. Therefore, the 16311 need only be accessed when the VFD status changes and when the button status is read. The MT1379 can control this chip directly using PIO pins or can allow the front panel PIC to control the VFD.
8
|
|
|
> |
|
